Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test)

Hee Bum Park, Yung Jin Kim, Sang Ki Park, Ki Hyung Lee

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

As recent vehicle industry has focused on global warming and air pollution, high thermal efficiency and eco-friendly engines with low CO2 emission levels have become more attractive. To meet strict future emission regulations, diesel engines are increasing interests due to its high efficiency. Higher injection pressure and multiple injections enable an improvement of air-fuel mixing characteristics and it makes increase of thermal efficiency and reduction of vehicle emissions. Therefore in these days, a piezo type injector with common-rail which has fast response and possibilities of multiple injections in shorter time is adopted for diesel engines instead of solenoid type injector. More powerful performance and accurate engine control are predicted with using piezo injector. Therefore in this paper, injection rate and spray image of multiple injections which are important design parameters for a piezo type injector have been investigated. Interval of injections and a number of injections in multiple injection strategy has been controlled to verify interaction of each injection. Characteristics of multiple injections have been researched through optical process with a high speed camera in a high pressure chamber. Also a method of RMS(Root Mean Square) process has been used for comprehending the distribution of injection easily. As a result, in case of piezo type injector, rapid response of injection was confirmed and spray characteristics of multiple injections were improved; multiple injections were possible in a shorter time interval between each injection. Penetration lengths become shorter and characteristics of evaporation get better.

Original languageEnglish
Title of host publicationProceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012
Pages659-664
Number of pages6
Publication statusPublished - 2012
Externally publishedYes
Event8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012 - Fukuoka, Japan
Duration: Jul 23 2012Jul 26 2012

Other

Other8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012
CountryJapan
CityFukuoka
Period7/23/127/26/12

Fingerprint

Injector
Spray
Experimental Study
Injection
Visualization
Diesel engines
Engines
Solenoids
High speed cameras
Global warming
Air pollution
Rails
Evaporation
Air
Diesel Engine
Industry
Hot Temperature
Engine Control
High-speed Camera
Global Warming

Keywords

  • Common-rail
  • High pressure chamber
  • Piezo injector
  • RMS(root mean square)

ASJC Scopus subject areas

  • Control and Systems Engineering
  • Modelling and Simulation

Cite this

Park, H. B., Kim, Y. J., Park, S. K., & Lee, K. H. (2012). Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test). In Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012 (pp. 659-664)

Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test). / Park, Hee Bum; Kim, Yung Jin; Park, Sang Ki; Lee, Ki Hyung.

Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012. 2012. p. 659-664.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Park, HB, Kim, YJ, Park, SK & Lee, KH 2012, Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test). in Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012. pp. 659-664, 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012, Fukuoka, Japan, 7/23/12.
Park HB, Kim YJ, Park SK, Lee KH. Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test). In Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012. 2012. p. 659-664
Park, Hee Bum ; Kim, Yung Jin ; Park, Sang Ki ; Lee, Ki Hyung. / Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test). Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012. 2012. pp. 659-664
@inproceedings{966e5764b988442badf855e36ded81f3,
title = "Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test)",
abstract = "As recent vehicle industry has focused on global warming and air pollution, high thermal efficiency and eco-friendly engines with low CO2 emission levels have become more attractive. To meet strict future emission regulations, diesel engines are increasing interests due to its high efficiency. Higher injection pressure and multiple injections enable an improvement of air-fuel mixing characteristics and it makes increase of thermal efficiency and reduction of vehicle emissions. Therefore in these days, a piezo type injector with common-rail which has fast response and possibilities of multiple injections in shorter time is adopted for diesel engines instead of solenoid type injector. More powerful performance and accurate engine control are predicted with using piezo injector. Therefore in this paper, injection rate and spray image of multiple injections which are important design parameters for a piezo type injector have been investigated. Interval of injections and a number of injections in multiple injection strategy has been controlled to verify interaction of each injection. Characteristics of multiple injections have been researched through optical process with a high speed camera in a high pressure chamber. Also a method of RMS(Root Mean Square) process has been used for comprehending the distribution of injection easily. As a result, in case of piezo type injector, rapid response of injection was confirmed and spray characteristics of multiple injections were improved; multiple injections were possible in a shorter time interval between each injection. Penetration lengths become shorter and characteristics of evaporation get better.",
keywords = "Common-rail, High pressure chamber, Piezo injector, RMS(root mean square)",
author = "Park, {Hee Bum} and Kim, {Yung Jin} and Park, {Sang Ki} and Lee, {Ki Hyung}",
year = "2012",
language = "English",
pages = "659--664",
booktitle = "Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012",

}

TY - GEN

T1 - Injection rate and spray characteristics of a piezo injector for multiple injection (Experimental study of a piezo injector through visualization test)

AU - Park, Hee Bum

AU - Kim, Yung Jin

AU - Park, Sang Ki

AU - Lee, Ki Hyung

PY - 2012

Y1 - 2012

N2 - As recent vehicle industry has focused on global warming and air pollution, high thermal efficiency and eco-friendly engines with low CO2 emission levels have become more attractive. To meet strict future emission regulations, diesel engines are increasing interests due to its high efficiency. Higher injection pressure and multiple injections enable an improvement of air-fuel mixing characteristics and it makes increase of thermal efficiency and reduction of vehicle emissions. Therefore in these days, a piezo type injector with common-rail which has fast response and possibilities of multiple injections in shorter time is adopted for diesel engines instead of solenoid type injector. More powerful performance and accurate engine control are predicted with using piezo injector. Therefore in this paper, injection rate and spray image of multiple injections which are important design parameters for a piezo type injector have been investigated. Interval of injections and a number of injections in multiple injection strategy has been controlled to verify interaction of each injection. Characteristics of multiple injections have been researched through optical process with a high speed camera in a high pressure chamber. Also a method of RMS(Root Mean Square) process has been used for comprehending the distribution of injection easily. As a result, in case of piezo type injector, rapid response of injection was confirmed and spray characteristics of multiple injections were improved; multiple injections were possible in a shorter time interval between each injection. Penetration lengths become shorter and characteristics of evaporation get better.

AB - As recent vehicle industry has focused on global warming and air pollution, high thermal efficiency and eco-friendly engines with low CO2 emission levels have become more attractive. To meet strict future emission regulations, diesel engines are increasing interests due to its high efficiency. Higher injection pressure and multiple injections enable an improvement of air-fuel mixing characteristics and it makes increase of thermal efficiency and reduction of vehicle emissions. Therefore in these days, a piezo type injector with common-rail which has fast response and possibilities of multiple injections in shorter time is adopted for diesel engines instead of solenoid type injector. More powerful performance and accurate engine control are predicted with using piezo injector. Therefore in this paper, injection rate and spray image of multiple injections which are important design parameters for a piezo type injector have been investigated. Interval of injections and a number of injections in multiple injection strategy has been controlled to verify interaction of each injection. Characteristics of multiple injections have been researched through optical process with a high speed camera in a high pressure chamber. Also a method of RMS(Root Mean Square) process has been used for comprehending the distribution of injection easily. As a result, in case of piezo type injector, rapid response of injection was confirmed and spray characteristics of multiple injections were improved; multiple injections were possible in a shorter time interval between each injection. Penetration lengths become shorter and characteristics of evaporation get better.

KW - Common-rail

KW - High pressure chamber

KW - Piezo injector

KW - RMS(root mean square)

UR - http://www.scopus.com/inward/record.url?scp=84877870791&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84877870791&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:84877870791

SP - 659

EP - 664

BT - Proceedings of the 8th International Conference on Modeling and Diagnostics for Advanced Engine Systems, COMODIA 2012

ER -