Influence of activation mode of dual-cured resin composite cores and low-viscosity composite liners on bond strength to dentin treated with self-etching adhesives

Marcelo Giannini, Mario F. De Goes, Toru Nikaido, Yasushi Shimada, Junji Tagami

Research output: Contribution to journalArticle

33 Citations (Scopus)

Abstract

Purpose: The objective of this study was to investigate the effect of light- or chemical initiation on the polymerization reaction of dual-cured composite core buildup materials (CM) with respect to their shear bond strength to dentin treated with self-etching adhesives (SE), in the presence or absence of a low-viscosity composite liner (LI). Materials and Methods: Two SEs (Clearfil SE Bond and Unifil Core Bond), their respective CMs (DC Core Paste and Unifil Core), and a LI (Protect Liner F) were tested. After removing the labial enamel surfaces of 8 bovine incisors, each flat dentin surface was sectioned into 4 pieces with similar surface areas (30 mm2). The dentin surfaces were wet abraded with 600-grit SiC paper and randomly divided into 8 groups. Experimental groups comprised the use of a SE and its respective CM with or without an intermediate application of the LI and with or without CM light activation. Three cylinders of CM (0.5 mm high and 0.75 mm in diameter) were applied to each bonded dentin surface (n = 12), using a tygon tubing mold. After water storage for 24 h, specimens were subjected to microshear testing. Data were statistically analyzed by two-way ANOVA and Tukey's test (5%). Results: For both SEs, LI application and CM light activation showed significantly higher bond strengths than the groups in which an intermediate LI was not used or the CMs were only chemically cured. Conclusion: The bond strength of CM to dentin using SE is reduced if the LI and light activation are not employed.

Original languageEnglish
Pages (from-to)301-306
Number of pages6
JournalJournal of Adhesive Dentistry
Volume6
Issue number4
Publication statusPublished - 2004
Externally publishedYes

Fingerprint

Composite Resins
Dentin
Viscosity
Adhesives
Light
Shear Strength
Incisor
Dental Enamel
Ointments
Lip
Polymerization
Analysis of Variance
Fungi
Water
Unifil Core

Keywords

  • Adhesive systems
  • Bond strength
  • Composite activation
  • Dentin
  • Resin core

ASJC Scopus subject areas

  • Dentistry(all)

Cite this

Influence of activation mode of dual-cured resin composite cores and low-viscosity composite liners on bond strength to dentin treated with self-etching adhesives. / Giannini, Marcelo; De Goes, Mario F.; Nikaido, Toru; Shimada, Yasushi; Tagami, Junji.

In: Journal of Adhesive Dentistry, Vol. 6, No. 4, 2004, p. 301-306.

Research output: Contribution to journalArticle

@article{0c12790cd0694556869024b35ee7b395,
title = "Influence of activation mode of dual-cured resin composite cores and low-viscosity composite liners on bond strength to dentin treated with self-etching adhesives",
abstract = "Purpose: The objective of this study was to investigate the effect of light- or chemical initiation on the polymerization reaction of dual-cured composite core buildup materials (CM) with respect to their shear bond strength to dentin treated with self-etching adhesives (SE), in the presence or absence of a low-viscosity composite liner (LI). Materials and Methods: Two SEs (Clearfil SE Bond and Unifil Core Bond), their respective CMs (DC Core Paste and Unifil Core), and a LI (Protect Liner F) were tested. After removing the labial enamel surfaces of 8 bovine incisors, each flat dentin surface was sectioned into 4 pieces with similar surface areas (30 mm2). The dentin surfaces were wet abraded with 600-grit SiC paper and randomly divided into 8 groups. Experimental groups comprised the use of a SE and its respective CM with or without an intermediate application of the LI and with or without CM light activation. Three cylinders of CM (0.5 mm high and 0.75 mm in diameter) were applied to each bonded dentin surface (n = 12), using a tygon tubing mold. After water storage for 24 h, specimens were subjected to microshear testing. Data were statistically analyzed by two-way ANOVA and Tukey's test (5{\%}). Results: For both SEs, LI application and CM light activation showed significantly higher bond strengths than the groups in which an intermediate LI was not used or the CMs were only chemically cured. Conclusion: The bond strength of CM to dentin using SE is reduced if the LI and light activation are not employed.",
keywords = "Adhesive systems, Bond strength, Composite activation, Dentin, Resin core",
author = "Marcelo Giannini and {De Goes}, {Mario F.} and Toru Nikaido and Yasushi Shimada and Junji Tagami",
year = "2004",
language = "English",
volume = "6",
pages = "301--306",
journal = "Journal of Adhesive Dentistry",
issn = "1461-5185",
publisher = "Quintessence Publishing Company",
number = "4",

}

TY - JOUR

T1 - Influence of activation mode of dual-cured resin composite cores and low-viscosity composite liners on bond strength to dentin treated with self-etching adhesives

AU - Giannini, Marcelo

AU - De Goes, Mario F.

AU - Nikaido, Toru

AU - Shimada, Yasushi

AU - Tagami, Junji

PY - 2004

Y1 - 2004

N2 - Purpose: The objective of this study was to investigate the effect of light- or chemical initiation on the polymerization reaction of dual-cured composite core buildup materials (CM) with respect to their shear bond strength to dentin treated with self-etching adhesives (SE), in the presence or absence of a low-viscosity composite liner (LI). Materials and Methods: Two SEs (Clearfil SE Bond and Unifil Core Bond), their respective CMs (DC Core Paste and Unifil Core), and a LI (Protect Liner F) were tested. After removing the labial enamel surfaces of 8 bovine incisors, each flat dentin surface was sectioned into 4 pieces with similar surface areas (30 mm2). The dentin surfaces were wet abraded with 600-grit SiC paper and randomly divided into 8 groups. Experimental groups comprised the use of a SE and its respective CM with or without an intermediate application of the LI and with or without CM light activation. Three cylinders of CM (0.5 mm high and 0.75 mm in diameter) were applied to each bonded dentin surface (n = 12), using a tygon tubing mold. After water storage for 24 h, specimens were subjected to microshear testing. Data were statistically analyzed by two-way ANOVA and Tukey's test (5%). Results: For both SEs, LI application and CM light activation showed significantly higher bond strengths than the groups in which an intermediate LI was not used or the CMs were only chemically cured. Conclusion: The bond strength of CM to dentin using SE is reduced if the LI and light activation are not employed.

AB - Purpose: The objective of this study was to investigate the effect of light- or chemical initiation on the polymerization reaction of dual-cured composite core buildup materials (CM) with respect to their shear bond strength to dentin treated with self-etching adhesives (SE), in the presence or absence of a low-viscosity composite liner (LI). Materials and Methods: Two SEs (Clearfil SE Bond and Unifil Core Bond), their respective CMs (DC Core Paste and Unifil Core), and a LI (Protect Liner F) were tested. After removing the labial enamel surfaces of 8 bovine incisors, each flat dentin surface was sectioned into 4 pieces with similar surface areas (30 mm2). The dentin surfaces were wet abraded with 600-grit SiC paper and randomly divided into 8 groups. Experimental groups comprised the use of a SE and its respective CM with or without an intermediate application of the LI and with or without CM light activation. Three cylinders of CM (0.5 mm high and 0.75 mm in diameter) were applied to each bonded dentin surface (n = 12), using a tygon tubing mold. After water storage for 24 h, specimens were subjected to microshear testing. Data were statistically analyzed by two-way ANOVA and Tukey's test (5%). Results: For both SEs, LI application and CM light activation showed significantly higher bond strengths than the groups in which an intermediate LI was not used or the CMs were only chemically cured. Conclusion: The bond strength of CM to dentin using SE is reduced if the LI and light activation are not employed.

KW - Adhesive systems

KW - Bond strength

KW - Composite activation

KW - Dentin

KW - Resin core

UR - http://www.scopus.com/inward/record.url?scp=12344266106&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=12344266106&partnerID=8YFLogxK

M3 - Article

VL - 6

SP - 301

EP - 306

JO - Journal of Adhesive Dentistry

JF - Journal of Adhesive Dentistry

SN - 1461-5185

IS - 4

ER -