Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium

Jun Oshitani, Soichiro Kajimoto, Mikio Yoshida, George V. Franks, Yasuo Kubo, Shingo Nakatsukasa

Research output: Contribution to journalArticle

18 Citations (Scopus)

Abstract

A continuous separator based on float-sink density separation using a gas-solid fluidized bed dense medium was used to upgrade iron ore. The separator has three devices for (A) conveying floaters, (B) recovering floaters, and (C) conveying and recovering sinkers. The optimum speeds of these devices were investigated using density adjusted spheres of the diameter = 30 mm in the range of 2400-3300 kg/m3 in density increments of 100 kg/m3. A mixture of zircon sand and iron powder was used as the fluidized medium to adjust the fluidized bed density to produce a separation density = 2850 kg/m3, a typical separation density for lump iron ore wet separation. The recovery of the spheres as floaters or sinkers depended on the speed of the devices, because the recovery was affected by the number density of spheres directly under the feeder, the local fluidized bed density, and flow currents in the medium derived from the movement of the devices. The optimum speeds were determined to be 3.5 cm/s for (A), 2.0 rpm for (B) and 1.0 cm/s for (C), respectively. Continuous separation experiments were conducted on lump iron ore particles in the size range of +11.1-31.5 mm in the fluidized bed with medium density of 2850 kg/m3 and feed rate of 200 kg/h. Comparison of the feed rate and the recovery rate indicated that the feed and the recovery were in equilibrium after 10 min of operation. The experiments resulted in nearly perfect separation; 98.4% of the ore with density greater than 2850 kg/m 3 was recovered. The Fe, Al and Si content of the feed ore particles (before the separation) and the floaters and sinkers (after the separation) was measured using inductively coupled plasma spectrometry. The separator produced an upgrade in iron content of 3.3 wt% and reduced the Al and Si content by 44%.

Original languageEnglish
Pages (from-to)468-472
Number of pages5
JournalAdvanced Powder Technology
Volume24
Issue number2
DOIs
Publication statusPublished - Mar 2013

Fingerprint

Iron ores
Fluidized beds
Sand
Separators
Recovery
Conveying
Ores
Zircon
Iron powder
Inductively coupled plasma
Spectrometry
Iron
Gases
Experiments

Keywords

  • Continuous separation
  • Dry dense medium
  • Fluidized bed
  • Iron ore
  • Mineral processing

ASJC Scopus subject areas

  • Chemical Engineering(all)
  • Mechanics of Materials

Cite this

Oshitani, J., Kajimoto, S., Yoshida, M., Franks, G. V., Kubo, Y., & Nakatsukasa, S. (2013). Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium. Advanced Powder Technology, 24(2), 468-472. https://doi.org/10.1016/j.apt.2012.10.010

Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium. / Oshitani, Jun; Kajimoto, Soichiro; Yoshida, Mikio; Franks, George V.; Kubo, Yasuo; Nakatsukasa, Shingo.

In: Advanced Powder Technology, Vol. 24, No. 2, 03.2013, p. 468-472.

Research output: Contribution to journalArticle

Oshitani, J, Kajimoto, S, Yoshida, M, Franks, GV, Kubo, Y & Nakatsukasa, S 2013, 'Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium', Advanced Powder Technology, vol. 24, no. 2, pp. 468-472. https://doi.org/10.1016/j.apt.2012.10.010
Oshitani, Jun ; Kajimoto, Soichiro ; Yoshida, Mikio ; Franks, George V. ; Kubo, Yasuo ; Nakatsukasa, Shingo. / Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium. In: Advanced Powder Technology. 2013 ; Vol. 24, No. 2. pp. 468-472.
@article{f199846ed44b4a90b7feb35374491579,
title = "Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium",
abstract = "A continuous separator based on float-sink density separation using a gas-solid fluidized bed dense medium was used to upgrade iron ore. The separator has three devices for (A) conveying floaters, (B) recovering floaters, and (C) conveying and recovering sinkers. The optimum speeds of these devices were investigated using density adjusted spheres of the diameter = 30 mm in the range of 2400-3300 kg/m3 in density increments of 100 kg/m3. A mixture of zircon sand and iron powder was used as the fluidized medium to adjust the fluidized bed density to produce a separation density = 2850 kg/m3, a typical separation density for lump iron ore wet separation. The recovery of the spheres as floaters or sinkers depended on the speed of the devices, because the recovery was affected by the number density of spheres directly under the feeder, the local fluidized bed density, and flow currents in the medium derived from the movement of the devices. The optimum speeds were determined to be 3.5 cm/s for (A), 2.0 rpm for (B) and 1.0 cm/s for (C), respectively. Continuous separation experiments were conducted on lump iron ore particles in the size range of +11.1-31.5 mm in the fluidized bed with medium density of 2850 kg/m3 and feed rate of 200 kg/h. Comparison of the feed rate and the recovery rate indicated that the feed and the recovery were in equilibrium after 10 min of operation. The experiments resulted in nearly perfect separation; 98.4{\%} of the ore with density greater than 2850 kg/m 3 was recovered. The Fe, Al and Si content of the feed ore particles (before the separation) and the floaters and sinkers (after the separation) was measured using inductively coupled plasma spectrometry. The separator produced an upgrade in iron content of 3.3 wt{\%} and reduced the Al and Si content by 44{\%}.",
keywords = "Continuous separation, Dry dense medium, Fluidized bed, Iron ore, Mineral processing",
author = "Jun Oshitani and Soichiro Kajimoto and Mikio Yoshida and Franks, {George V.} and Yasuo Kubo and Shingo Nakatsukasa",
year = "2013",
month = "3",
doi = "10.1016/j.apt.2012.10.010",
language = "English",
volume = "24",
pages = "468--472",
journal = "Advanced Powder Technology",
issn = "0921-8831",
publisher = "Elsevier BV",
number = "2",

}

TY - JOUR

T1 - Continuous float-sink density separation of lump iron ore using a dry sand fluidized bed dense medium

AU - Oshitani, Jun

AU - Kajimoto, Soichiro

AU - Yoshida, Mikio

AU - Franks, George V.

AU - Kubo, Yasuo

AU - Nakatsukasa, Shingo

PY - 2013/3

Y1 - 2013/3

N2 - A continuous separator based on float-sink density separation using a gas-solid fluidized bed dense medium was used to upgrade iron ore. The separator has three devices for (A) conveying floaters, (B) recovering floaters, and (C) conveying and recovering sinkers. The optimum speeds of these devices were investigated using density adjusted spheres of the diameter = 30 mm in the range of 2400-3300 kg/m3 in density increments of 100 kg/m3. A mixture of zircon sand and iron powder was used as the fluidized medium to adjust the fluidized bed density to produce a separation density = 2850 kg/m3, a typical separation density for lump iron ore wet separation. The recovery of the spheres as floaters or sinkers depended on the speed of the devices, because the recovery was affected by the number density of spheres directly under the feeder, the local fluidized bed density, and flow currents in the medium derived from the movement of the devices. The optimum speeds were determined to be 3.5 cm/s for (A), 2.0 rpm for (B) and 1.0 cm/s for (C), respectively. Continuous separation experiments were conducted on lump iron ore particles in the size range of +11.1-31.5 mm in the fluidized bed with medium density of 2850 kg/m3 and feed rate of 200 kg/h. Comparison of the feed rate and the recovery rate indicated that the feed and the recovery were in equilibrium after 10 min of operation. The experiments resulted in nearly perfect separation; 98.4% of the ore with density greater than 2850 kg/m 3 was recovered. The Fe, Al and Si content of the feed ore particles (before the separation) and the floaters and sinkers (after the separation) was measured using inductively coupled plasma spectrometry. The separator produced an upgrade in iron content of 3.3 wt% and reduced the Al and Si content by 44%.

AB - A continuous separator based on float-sink density separation using a gas-solid fluidized bed dense medium was used to upgrade iron ore. The separator has three devices for (A) conveying floaters, (B) recovering floaters, and (C) conveying and recovering sinkers. The optimum speeds of these devices were investigated using density adjusted spheres of the diameter = 30 mm in the range of 2400-3300 kg/m3 in density increments of 100 kg/m3. A mixture of zircon sand and iron powder was used as the fluidized medium to adjust the fluidized bed density to produce a separation density = 2850 kg/m3, a typical separation density for lump iron ore wet separation. The recovery of the spheres as floaters or sinkers depended on the speed of the devices, because the recovery was affected by the number density of spheres directly under the feeder, the local fluidized bed density, and flow currents in the medium derived from the movement of the devices. The optimum speeds were determined to be 3.5 cm/s for (A), 2.0 rpm for (B) and 1.0 cm/s for (C), respectively. Continuous separation experiments were conducted on lump iron ore particles in the size range of +11.1-31.5 mm in the fluidized bed with medium density of 2850 kg/m3 and feed rate of 200 kg/h. Comparison of the feed rate and the recovery rate indicated that the feed and the recovery were in equilibrium after 10 min of operation. The experiments resulted in nearly perfect separation; 98.4% of the ore with density greater than 2850 kg/m 3 was recovered. The Fe, Al and Si content of the feed ore particles (before the separation) and the floaters and sinkers (after the separation) was measured using inductively coupled plasma spectrometry. The separator produced an upgrade in iron content of 3.3 wt% and reduced the Al and Si content by 44%.

KW - Continuous separation

KW - Dry dense medium

KW - Fluidized bed

KW - Iron ore

KW - Mineral processing

UR - http://www.scopus.com/inward/record.url?scp=84876140526&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84876140526&partnerID=8YFLogxK

U2 - 10.1016/j.apt.2012.10.010

DO - 10.1016/j.apt.2012.10.010

M3 - Article

AN - SCOPUS:84876140526

VL - 24

SP - 468

EP - 472

JO - Advanced Powder Technology

JF - Advanced Powder Technology

SN - 0921-8831

IS - 2

ER -